RSC Advances PAPER O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online View Journal | View Issue Effect of temper aFraunhofer-Institute for Interfacial Enginee 70569 Stuttgart, Germany. E-mail: solyomka bSchool of Food Technology, University of C Cite this: RSC Adv., 2020, 10, 16783 Received 17th December 2019 Accepted 14th March 2020 DOI: 10.1039/c9ra10639a rsc.li/rsc-advances This journal is © The Royal Society o ature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Katalin Solyom, *a Pilar Rosales Lopez,a Patricia Esquivel,b Ana Luciaa and Vásquez- Caicedoa Microwave heating is a part of several food processing unit-operations, while also emerging as a processing technology for by-products. Process efficiency depends on dielectric properties; however, data of these by-products are scarce in literature. The present study is focused on the effect of temperature and moisture content (M) on the dielectric constant (30) and loss (300) of carrot waste, apple pomace, pineapple peel and spent coffee grounds at 2.45 GHz. Results on 30 showed moisture-dependent temperature effect with an inflection point at M ¼ 50.3%. The 300 increased with increasing M up to 60% and decreased at higher moisture levels. Results at different temperatures were significantly affected by the composition of the studied materials and thus the calculated power penetration depth. Although fresh food dielectric properties are available in literature, the data is not always suitable to estimate food waste properties as processing may cause compositional changes. The obtained results support microwave process optimization in the field of food-waste valorization. Introduction Fruit and vegetable processing industries produce millions of tons of by-products, including peels, seeds, stones, residual pulp and others. If not disposed of or treated, these waste products are considered environmental hazards due to the emission of greenhouse gases during decomposition. Moreover, the valorization of these waste products has been discussed due to their potential as bioactive compound sources.1 Several efforts have been described in order to take advantage of food wastes. The extraction of carotenoids from carrot peels,2 the valorization of apple pomace by the extraction of valuable compounds,3 the extraction of bioactive compounds and glycosides from pineapple peels4 as well as the potential of spent coffee grounds as a source of polyphenols5 are some examples of the broad research focused on exploiting the industrial potential of by-products from the fruit and vegetable processing industries. These bioactives gained importance due to their association with several health benets but extraction methods are still a challenge.6 Modern green extraction techniques have been developed with the goal of exploiting bioactive compounds using more eco-friendly, efficient and cost-effective techniques.6 Among the different novel extraction technologies, microwave-assisted extraction has emerged as a promising ring and Biotechnology, Nobelsrtaße 12, talin@gmail.com osta Rica, 2060 San Pedro, Costa Rica f Chemistry 2020 alternative providing highly efficient recovery due to shorter extraction time and lower solvent usage.6–8 Moreover, the enhancement of the microwave combustion efficiency of food waste has been assessed, and the effects and impact on the food components have been broadly reviewed.9,10 For the application of microwave technologies, research on the DPs of the materials under study is required.11 Besides comprehensive studies on optimized process conditions for both extraction and drying purposes using microwaves, it is essential to know how the materials in question interact with the electromagnetic eld at which they are subjected to in order to facilitate the proper microwave reactor design on a larger scale. This interaction is described by the complex dielectric permittivity (eqn (1)–(3)) of the material.12 3 ¼ 303r (1) 3r ¼ 3 0 r + j3 00 r (2) tan d ¼ 3 00 r 3 0 r (3) dp ¼ c 2pf ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 230r " ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1þ �300r 3 0 r �2 s � 1 #vuut (4) In eqn (1), 30 and 3r refer to the free space permittivity and the complex permittivity, respectively. eqn (2) shows the real RSC Adv., 2020, 10, 16783–16790 | 16783 http://crossmark.crossref.org/dialog/?doi=10.1039/c9ra10639a&domain=pdf&date_stamp=2020-04-28 http://orcid.org/0000-0002-7550-1032 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a https://pubs.rsc.org/en/journals/journal/RA https://pubs.rsc.org/en/journals/journal/RA?issueid=RA010028 RSC Advances Paper O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online part of the complex permittivity, i.e., dielectric constant (3 0 r), which corresponds to the energy stored in the material when an electric eld is applied and the imaginary part (3 00 r ) corresponding to the energy is converted into heat. The ratio between the imaginary and the real part is tan d, the tangent loss (eqn (3)), which measures the ability of the food matrix to absorb microwave energy and dissipate heat to the surrounding molecules, being responsible for the efficiency of microwave heating. The tangent loss also plays an important role in the determination of the penetration depth of microwave power (eqn (4)), which is dened as the depth where the power is reduced to 1/e (e ¼ 2.718) of the power entering the surface of the material. Through the calculation by eqn (4), the penetra- tion depths (dp) are given in meters, where c is the speed of light in free space (3 � 108 m s�1), and f is the frequency in Hz. Chemical composition, seasonal variation, physical struc- ture, frequency, temperature and moisture content affect most of the dielectric properties (DP) of the foodmatrix. For vegetable and fruit samples, the dielectric constant and conductivity largely depend on the moisture content, as inuenced by frequency, temperature, density and particle size.13,14 These characteristics may vary during the microwave process as the material undergoes physical and perhaps, chemical changes (e.g. moisture content, temperature and salt concentration), which would affect its interaction with the dielectric eld.15 Thus, these factors must be taken into account when charac- terizing the dielectric properties of the sample. Although there is available literature on the DP of fresh vegetables and fruits, considering changes in moisture and temperature,16–18 comprehensive studies on the DPs of by- products from fruit and vegetable processing are still scarce. Therefore, the aim of this study is to observe the direct effects of temperature and moisture content on the DP of the selected wastes at 2.45 GHz, while taking into consideration the changing volume fraction of the product. Table 1 Experimental design for the dielectric properties measure- ment of carrot waste (CW), apple pomace (AP), pineapple peer (PP) and spent coffee grounds (SCG) at different moisture (M) and temperature (T) levels Carrot waste Apple pomace Pineapple peel Spent coffee grounds Moisture (%) 90.4 77.8 86.7 58.2 69.3 61.0 69.0 48.2 64.6 51.1 54.0 42.6 31.6 31.8 38.2 23.5 Temperature (�C) 27.1 24.4 23.0 22.2 40.9 42.6 42.2 34.2 56.9 59.0 58.9 43.5 68.3 74.6 72.5 51.8 Experimental Raw material Carrot waste (CW). Carrot waste was prepared in the labo- ratory for experimentation. Taking into account that the carrot waste was about 30% of the carrot without leaves,19 6 kg of carrot from a local supermarket was used for the experiments. Both extremes of the root were cut and the rest was scrapped, obtaining two kilograms of waste in total. The proportion of defected chunks, by decision, were one-sixth of the total waste mass, the rest were scrapped peels and both extremes of the root. Homogeny samples were obtained by chopping using a household appliance (Quad blade chopper, Kenwood CH580, 500 W, 0.5 L) for 10 s at a low speed for carrot waste. Apple pomace (AP). Apple pomace was obtained from the Hohenheim University, Plant Foodstuff Technology and Anal- ysis Department as a residue of the production of apple juice. The total residue was a mixture of 4 types of apple: Jonagold, Braeburn, Boskop and Pink lady, and it contained peels, pomace and seeds. Sample homogeneity was obtained by 16784 | RSC Adv., 2020, 10, 16783–16790 chopping using a household appliance (used as well for CW) for 20 s. Pineapple peel (PP). Approximately 10 kg of Golden extra pineapples (the sweet type) were bought at a local supermarket (ca. 8 pineapples without leaves) and subsequently washed with cold water. In accordance with previous studies, the mass of the chopped peels obtained was approximately 3.3 kg, representing one-third of the total mass.19 Due to their roughness, the peels were chopped for 20 s as described for CW and AP. Spent coffee ground (SCG). Coffee residues (100% Arabica- harmonisch coffee Hochland Kaffee Hunzelmann GmbH & Co. KG) were collected from the cafeteria at the Fraunhofer Campus IZS in Stuttgart. Spent from fresh milled and brewed coffee was further used as samples for this study. All raw materials were well mixed and distributed into bags of 250 grams each, and stored at �20 �C. Samples were thawed at 4 �C overnight before analysis. Moisture content determination The moisture content of the samples (approx. 3 g), was deter- mined in triplicate with an infrared moisture analyzer (MB45 Moisture Analyzer, Ohaus, Pine Brook NJ, USA), programmed to ascend gradually to 105 �C and switch-off automatically 60 s aer the mass difference is lower than 1 mg. The moisture content of the samples was given in weight percent (wt%). Samples for determining the effect of moisture content, were prepared in a hot-air drying oven (Binder FD53, drying oven with forced convection) at 80 �C in order to obtain three levels of moisture, different from the initial moisture content (Table 1). Drying times corresponding to the desired moisture level were previously determined (data not presented) and applied in this study. Temperature determination Samples for determining the effect of temperature were prepared at room temperature, followed by heating for 20 min in a hot-air drying oven at 50, 75, 100 �C. To enable better control of the temperature aer the heating process the samples were covered with an aluminium foil. The exact temperature wasmeasured during the determination of dielectric properties. This journal is © The Royal Society of Chemistry 2020 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a Paper RSC Advances O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online Density measurement Particle density. The sample density was measured in trip- licate in a glass pycnometer, lled with the sample at different moisture contents and distilled water. Bulk density. Due to the preparation method of the raw materials, particulate forms were obtained and were studied as a bulk material. Each sample had the same weight and bulk volume in the examining tubes. The bulk density of these samples was calculated as follows (eqn (5)): rb ¼ mvþs �mv mvþw �mv (5) where rb is the bulk density,m(v+s) is the mass of the vial and the sample,m(v+w) is the mass of the vial and water andmv is the vial mass. The volume was estimated with distilled water (density ¼ 1 g mL�1), so the mass measurements can be directly converted into volume dimension. Dielectric properties (DP) measurement Dielectric Measurement Kit mWaveAnalyzer (Püschner GmbH, Bremen, Germany) using a cavity perturbation method at 2.45 GHz was applied for the determination of DP. The measure- ment kit (Fig. 1) consists of A “Microwave Analyzer” composed of a microwave generator, a microwave receiver and a USB data acquisition system and an “Open-ended Coaxial Probe Cavity” made of high-end stainless steel. Polypropylene tubes (D ¼ 12 mm, H ¼ 75 mm) containing exact mass (between 1.70 and 4.22 g, regarding waste material and moisture content) were used to t a constant volume of the material, which was placed into the cavity. The maintenance of the exact material amount between measured replicates is of the highest importance as it directly inuences the bulk density in the measurement tubes and the accuracy of the measurement. From the determined resonant frequency and the quality factor of the empty and l- led cavity, the complex permittivity was calculated through the supplied soware (Measurement Kit, Vials v3.01). Experimental design Due to the nature of the raw materials and former experience,20 large deviations were expected from the measurements. Therefore, it was necessary to apply an extensive experimental design including several repetitions. A full factorial design was applied for two factors, tempera- ture (T [�C]) and moisture (M [%]), each at four levels (Table 1). Fig. 1 Dielectric measurement device. This journal is © The Royal Society of Chemistry 2020 The highest moisture was the initialM level of the raw material, and further 3 points were achieved via drying. The lowest temperature was room temperature, and further three T levels were achieved via heating. The experimental design included 18 measurement points: 16 points with the moisture (M1–M4) and temperature (T1–T4) combination, and two additional experi- ments forM3 and T3. Each measurement point was measured in ve replicates. Statistical analysis The dielectric properties of ve replicates were measured and evaluated using one-way ANOVA (p # 0.05) in order to deter- mine if there was a signicant effect of the temperature and moisture content. Deected results from the replicates were eliminated (never more than two) by applying the Grubb's test. In addition, M3–T3 experiments were repeated three times and were analyzed using one-way ANOVA (p # 0.05) to support the premise of no signicant difference between the three trials. Statistical analysis was performed using OriginLab® 2015 (OriginLab Corporation Northampton, Massachusetts, USA). Linear and polynomial regression on experimental data such as the calculation of correlation coefficient was performed with Microso Excel® using the least squares method. The main text of the article should appear here with appropriate headings. Calculation The used waste material was present as a particle-air mixture in the measurement tubes, in which fractions may vary at different moisture content and temperature levels. The DP measurement procedure provided a result of the material, which was present in the measurement cavity. Therefore, the measured data had to be evaluated through an air-particle mixing equation in order to extract reliable data on the characteristics of the pure material. Based on previous experience on grape marc,20 the complex refractive indexmixture equation (CRIM) was found to be suitable for food by-products and thus used in this study (eqn (6)):ffiffiffiffiffi 3m p ¼ v1 ffiffiffiffi 31 p þ v2 ffiffiffiffi 32 p (6) where 3m refers to the dielectric property of the air-material mixture, 31 and 32 correspond to the air and material phases, and n1 and n2 refer to their volume fractions (porosity) in the sample. Such correlation between experimental data and suitable models are widely used in literature in order to obtain compa- rable results on the dielectric properties of porous materials.21 Measured data were obtained from experimental sets, where the bulk density and particle density were maintained close to each other in order to reach the highest correlation between modeled and measured values. Estimated results of pure material are presented and discussed throughout the study. Results and discussion Effect of moisture on dielectric constant Results showed a similar increasing tendency with increasingM for all studied material at all temperatures (Fig. 2). This RSC Adv., 2020, 10, 16783–16790 | 16785 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a Fig. 2 Effect of moisture on food waste dielectric constant at all temperature levels. RSC Advances Paper O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online phenomenon can be attributed to the increase in free water available in the matrix, moving 30 towards the properties of pure water, 30 ¼ 80.14,22 In the case of CW, AP and PP, the same linear approximation (Fig. 2, eqn (7)) was found with the correlation coefficients of 0.972, 0.973 and 0.985, respectively, independent of their matrix. 3 0 CW;AP;PP ¼ 0.84M � 12.07 (7) where 3 0 CW;AP;PP is the estimated dielectric constant of carrot peel, apple pomace and pineapple peel, and M is the moisture content. Calay et al.23 derived predictive equation from available experimental data for various food matrixes, including fresh fruit and vegetable as well (eqn (8)): 3’ ¼ 2.14 � 0.104T + 0.808M (8) The equation to estimate 30 of Calay's study (eqn (7))23 ts well with the experimental data of our study: correlation coef- cients of 0.976, 0.974 and 0.985 for CW, AP and PP, respec- tively, which have not suffered any chemical alteration. Accordingly, our results show that 30 of the studied wastes could Fig. 3 (a) Effect of temperature on 30 of apple pomace and (b) moisture 16786 | RSC Adv., 2020, 10, 16783–16790 be estimated from available data in the literature of fresh fruits and vegetables. However, these predictive equations did not t the results of SCG. Moreover, 30 showed an increasing tendency with increasing M for SCG; these values were lower than the ones of the other studied materials at the comparable M range (30– 60%). The presented food wastes had different origins. CW and PP were only subjected to peeling; they still retained their original composition. However, AP has been produced by a pressing process, which has not altered the composition of the peel but strongly affected the esh. In contrast, SCG originated from an extraction process using water at an elevated temper- ature that strongly affected the chemical composition of the original material. Coffee is rich in bers, oil and water-soluble components such as sugar. According to other studies, sugar could not be detected in the chemical analysis of SCG as it is commonly extracted through the coffee brewing process.24,25 However, the sugar content was found to be the most signicant component to model dielectric properties in products such as grapes or juices;26,27 thus, the absence of it in SCG could diminish the dielectric constant values. Results for SCG can be well described (correlation coefficient of 0.998) with a second-order polynomial t (eqn (9)). 3 0 SCG ¼ 0.016M2 � 0.812M + 18.81 (9) However, no literature was found on similar material at 2.45 GHz; results on parchment coffee have reported a third-order polynomial t between 0.1–10 MHz for different moisture contents.28 Effect of temperature on dielectric constant In the case of CW, AP and PP, M dependent temperature effect was observed on 30 values. Increasing T caused a linear change (as an example, AP is shown in Fig. 3a), resulting in an increased slope by decreasing the moisture content. The overall effect is shown in Fig. 3b, where linear dependency was observed (correlation coefficient ¼ 0.9346) irrespective of the type of sample. According to the correlation, M > 50.30% causes a decrease in 30 with increasing T, and below this value 30 will increase with the increase in T. The latter observation was found to be typical for fresh fruits, vegetables13 and berries.29 Barba and d'Amore30 dependent slope of T(30) linear fit. This journal is © The Royal Society of Chemistry 2020 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a Fig. 4 Temperature effect on the dielectric constant of spent coffee grounds. Fig. 5 Effect of the moisture content on the dielectric loss at room temperature. Paper RSC Advances O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online described two phenomena corresponding to the temperature effect on dielectric properties: (1) increment of 30 is expected as bounded dipoles become more available to the orientation effects of the electromagnetic eld at higher temperatures. (2) A large amount of free water in the system solubilize sugar, starch and mineral components, which enables the material to better dissipate energy into heat at a higher temperature. Conse- quently, a reductive effect on the energy storage and thus on the dielectric constant can be observed. The combination of these two effects in the material will determine the nal dielectric behaviour under changing temperature. In contrast to the former ndings, 30 of SCG did not show any signicant change (P < 0.5) against increasing temperature (Fig. 4). The composition of SCG ismostly limited to proteins, crude bers, lignin, cellulose and lipids,24 thus having more similarity to agri- cultural products, such as cereal grains with a low moisture content. However, for such material, no general behaviour has been found.31 According to Nelson, in the case of agricultural products, the results depended on variety and moisture content. Effect of moisture content on dielectric loss The dielectric loss increased with moisture content until a maximum level and then decreases at M > 50% in the case of AP andM > 70% in the cases of CW and PP (Fig. 5). In the case of SCG, 300 increased throughout the whole range. The highest studied moisture content was the initial one of the waste material. Therefore, no extrapolation should be made for conditions over the studied moisture range. The increasing tendency has been explained by the free water content amount of the matrix in other studies.13,26,30,32 At low moisture levels water correspondedmostly to the bounded form (physically absorbed to the dry surface), showing a eld oscil- lation. With the increment in water, critical moisture can be achieved for molecules in the matrix, where the water is found as a free form (found in capillaries) increasing the dielectric loss of the matrix. The critical moisture content is matrix and component-dependent, and in the present study, it was only observed in the case of SCG between M ¼ 42% and 48%. This journal is © The Royal Society of Chemistry 2020 When the dielectric loss of CW and PP reaches their maximum, (Mz 70%) dissolved components (salts, sugars) are at the saturation level. Higher moisture contents dilute the solution, which leads to lower measured values.32 Due to the saturation level of soluble compounds, increased 300 values were expected and conrmed (Fig. 6a) with the increase in temper- ature through higher solubilization of the components in the case of CW. Similar to the observed tendency for AP, the drying of red delicious apples showed a rapid increase in 300 untilMz 50% and slight increasing or even stable 300 values over that moisture.33 Comparing the waste materials, 300 values follow a tendency of CW > PP > AP > SCG, which can be attributed to their different chemical compositions. High ber (35–44%) and lipid (22–27%) content24 of SCG maintain its 300 low. These components not only express limited dipolar polarisation but also negatively affect the availability of free water in the matrix.32 Moreover, SCG disposed of low ash content of 1.3%,25 contributing to a moderate loss factor.32 According to earlier reports,34–37 relations between ash contents on the dry material basis of CW z 10%, PP z 4.5% and AP z 2–3.5% follow the same tendency as their 300 values. The observed effect of the ash content on the loss factor was previously described for foods by38 referring to the increased ionic component in the matrix. Effect of temperature on dielectric loss The temperature effect on the food matrix's loss factor can be affected by several factors such as moisture content and chemical composition. These factors have been reviewed in different studies13,23,29,32,39 and the following conclusions have been drawn: the presence of free water causes 300 to decrease with increasing temperature, while at lower moisture levels, where bound water content is signicant, and 300 will increase with temperature. In the case of salt solutions, a double effect of the dipole and ionic loss plays an important role. In the case of lower salt concentrations (<1%) dipole loss dominates, resulting in a decrease in 300. However, over a certain salt concentration, depending on the food matrix, the dominating ionic loss leads to an increase in 300 at RSC Adv., 2020, 10, 16783–16790 | 16787 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a Fig. 6 Effect of temperature on dielectric loss for (a) carrot waste (CW), (b) apple pomace (AP), (c) pineapple peel (PP) and (d) spent coffee grounds (SCG). RSC Advances Paper O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online higher temperatures. Sugar content will diminish the loss factor as the temperature rises. The studied matrices here, showed different behavior with increasing temperature (Fig. 6a–d). The dielectric loss of CW (Fig. 6a) at M1 (90.4%) was lower than at M2 (69.4%) at every temperature. Moreover, the dielectric loss of CW at M2 showed an increasing tendency, probably due to the higher salt concentration at M1. Previous studies evaluating the effect of salt contents in rice samples showed that the dielectric loss factor increased when salt was added.40 A clear tendency for 300 at M1 and M3 (64.6%) has not been observed due to the equalizing effects of the components. Results obtained at M4 (31.6%) slightly increased with temper- ature, this time affected by the remained bound water content in the carrot matrix. In the case of PP (Fig. 6c) no clear tendencies have been observed for M1, M2, and M3. Nevertheless, the material at M2 (61.04%), related to higher ionic loss and still signicant free water content increased with temperature. The origin of AP and SCG are different from the other materials, as discussed in a former section. Due to the pro- cessing, their soluble fraction was lower and therefore cannot contribute signicantly to the dielectric loss. Slightly decreasing 300 have been measured for AP (Fig. 6b) as well as for SCG (Fig. 6d) at M1 (58.2%). The dielectric loss of SCG remained mostly unaffected by temperature due to the synergic effect of bound water and considerable oil content.32 Effect of moisture content and temperature on penetration depth The calculated penetration depth of CW, AP, PP and SCG showed dispersed behaviour as affected by temperature and 16788 | RSC Adv., 2020, 10, 16783–16790 moisture content (Fig. 7). It was expected from other studies41–43 that at lower moisture levels higher penetration depth can be reached as the high dielectric constant of water responsible for the energy absorption at the surface. However, the effect of temperature was diverse in those studies and depended on the food moisture content. In the case of carrot peel (Fig. 7a) and pineapple peel (Fig. 7c) dp decreased at all moisture levels when the temperature increases. Similar behaviour was observed for rice bran,41 pistachios,42 potato starch and apple at lowmoisture contents.42 Both waste products showed an initial decrease in dp when moisture content decreased; however, at M lower than 69%, an increase in dp was observed. This may have occurred due to observation of the maximum values of 300 in the case of CW and PP (Fig. 5), and can be connected to the saturation level of dissolved components. The results of apple pomace (Fig. 7b) and spent coffee grounds (Fig. 7d) dp showed an increasing trend of higher temperatures, which was also observed for potato starch41 at high moisture contents as well as for various fruits studied at 2.45 GHz.29,43 In case of the effect of the moisture content, the behaviour of AP and SCG was contradictory: dp of AP decreased with the decrease in M, while dp of SCG increased at lower moisture contents. Latter behaviour was also described for other food matrices.41,42,44 The presented values are of importance in order to under- stand the power absorption of the food matrix and heat and mass transfer during a microwave-assisted process.45 In order to extract process-relevant data on penetration depth, the actual porosity of the sample must be taken into account (eqn (6)) as well as the dielectric properties of other materials involved, such as solvents, e.g., in the case of extraction processes. This journal is © The Royal Society of Chemistry 2020 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a Fig. 7 Power penetration depth at 2.45 GHz of (a) carrot waste, (b) apple pomace, (c) pineapple peel, (d) spent coffee grounds. Paper RSC Advances O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online Conclusions Dielectric constant and loss of carrot waste, apple pomace, pine- apple peel and spent coffee grounds were studied under different temperatures and moisture content by open-ended coaxial cavity at 2.45 GHz. The complex effect of the temperature, moisture and effect of composition differences were observed on the results. The moisture content (M) of the material was found to be critical: atM < 50.3%, 30 increasedwith the increase in temperature, while above this moisture level a decrease in 30 was observed.M < 60% showed an increasing effect on 300, while 300 decreased at a higher moisture content. Results were compared with literature data for carrot waste and pineapple peel, where no composition changes may have occurred through the waste generation. In contrast, apple pomace and spent coffee grounds have shown different results from that found in the literature. These differences also affected the calculated penetration depth of the studied materials. Thus, it was suggested that when considering food waste processing with the microwave technology, the dielectric behaviour of fresh food material should not be taken into account without considering composition similarity between fresh food and food waste. The emerging interest in food waste valorisation by the microwave technology, such as extraction and drying processes, opens the need for further studies on the dielectric properties of food waste. Conflicts of interest There are no conicts of interest to declare. Acknowledgements This project has received funding from the European Union's Horizon 2020 research and innovation program under the This journal is © The Royal Society of Chemistry 2020 Marie Sklodowska-Curie grant agreement No. 661198. Also, the research stay of Pilar Rosales López was funded by Baden Württemberg Foundation. References 1 A. Saini, P. S. Panesar and M. B. Bera, Bioresour. Bioprocess., 2019, 6(1), 26. 2 V. Lima, Food Chem., 2005, 90(4), 565. 3 C. A. Perussello, Z. Zhang, A. Marzocchella and B. K. Tiwari, Compr. Rev. Food Sci. Food Saf., 2017, 16(5), 776. 4 L. Sepúlveda, A. Romańı, C. N. Aguilar and J. Teixeira, Innovative Food Sci. Emerging Technol., 2018, 47, 38. 5 N. A. Al-Dhabi, K. Ponmurugan and P. Maran Jeganathan, Ultrason. Sonochem., 2017, 34, 206. 6 K. Ameer, H. M. Shahbaz and J. H. Kwon, Compr. Rev. Food Sci. Food Saf., 2017, 16(2), 295. 7 B. Hiranvarachat and S. Devahastin, J. Food Eng., 2014, 126, 17. 8 F. G. Chizoba Ekezie, D. W. Sun, Z. Han and J. H. Cheng, Trends Food Sci. Technol., 2017, 67, 58. 9 H. Liu, E. Jiaqiang, X. Ma and C. Xie, Drying Technol., 2016, 34(12), 1397. 10 H. Jiang, Z. Liu and S. Wang, Crit. Rev. Food Sci. Nutr., 2018, 58(14), 2476. 11 V. Meda, V. Orsat, and V. Raghavan, in The Microwave Processing of Foods, ed. M. Regier, K. Knoerzer, and H. Schubert, 2nd edn, 2017, ch. 2, pp. 23–43. 12 A. C. Metaxas and R. J. Meredith, Industrial Microwave Heating, Peter Perigrinus, London, 1983. 13 S. N. Jha, K. Narsaiah, A. L. Basediya, R. Sharma, P. Jaiswal, R. Kumar and R. Bharwaj, J. Food Sci. Technol., 2011, 48(4), 387. RSC Adv., 2020, 10, 16783–16790 | 16789 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a RSC Advances Paper O pe n A cc es s A rt ic le . P ub lis he d on 2 9 A pr il 20 20 . D ow nl oa de d on 6 /1 7/ 20 21 9 :3 0: 10 P M . T hi s ar tic le is li ce ns ed u nd er a C re at iv e C om m on s A ttr ib ut io n- N on C om m er ci al 3 .0 U np or te d L ic en ce . View Article Online 14 W. Routray and V. Orsat, Curr. Opin. Food Sci., 2018, 23, 120. 15 M. S. Venkatesh and G. S. V. Raghavan, Biosyst. Eng., 2004, 88(1), 1. 16 W. C. Dunlap and B. Makower, J. Phys. Chem., 1945, 49(6), 601. 17 S. O. Nelson, W. R. Forbus Jr and K. C. Lawrence, Trans. ASAE, 1994, 37(1), 183. 18 P. Kumar, P. Coronel, J. Simunovic, V. D. Truong and K. P. Sandeep, J. Food Sci., 2007, 72(4), E177. 19 J. Gustavsson, C. Cederberg, U. Sonesson, R. van Otterdijk and A. Meybeck, Global Food Losses and Food Waste – extent, causes and prevention, FAO, Rome, 2011. 20 K. Solyom, S. Kraus, R. B. Mato, V. Gaukel and H. P. Schuchmann, J. Food Eng., 2013, 119, 33. 21 Y. Liu, J. Tang and Z. Mao, J. Food Eng., 2009, 93(1), 72. 22 S. Ryynänen, J. Food Eng., 1995, 26, 409. 23 R. K. Calay, M. Nweborough, D. Probert and P. S. Calay, Int. J. Food Sci. Technol., 1994, 29, 699. 24 A. S. Franca and L. S. Oliviera, in Agricultural Wastes, ed. G. S. Asworth, and P. Azevedo, Nova Science Publishers, New York, 2009, ch. 8, p. 155. 25 L. F. Ballesteros, J. A. Teixeira and S. I. Mussatto, Food Bioprocess Technol., 2014, 7, 3493. 26 T. N. Tulasidas, G. S. V. Raghavan, F. van de Voort and R. Girard, J. Microw. Power Electromagn. Energy, 1995, 30(2), 117. 27 M. T. K. Kubo, S. Curet, P. E. D. Augusto and L. Boillereaux, J. Food Process Eng., 2018, e12815. 28 P. A. Berbert, D. M. Queiroz, E. F. Sousa, M. B. Molina, E. C. Melo and L. R. Faroni, J. Agric. Eng. Res., 2001, 80, 65. 29 M. E. Sosa-Morales, T. Flores-Lopez, D. E. Miranda-Estrada, T. Kaur Kataria, M. del R. Abraham-Juarez, A. Ceron-Garcia, A. Corona-Chavez, J. L. Olvera-Cervantes and R. J. Rojas- Laguna, J. Berry Res., 2017, 7, 239. 16790 | RSC Adv., 2020, 10, 16783–16790 30 A. A. Barba and M. d'Amore, Relevance of Dielectric Properties in Microwave Assisted Processes, in Microwave Materials Characterization, ed. S. Costanzo, IntechOpen, 2012, ch. 6, ISBN 978-953-51-0848-1, DOI: 10.5772/2687. 31 S. O. Nelson, Cereal Chem., 1981, 58(6), 487. 32 A. K. Datta, G. Sumnu and G. S. V. Raghavan, in Engineering Properties of Foods, ed. M. A. Rao, S. H. Rizvi and A. K. Datta, CRC Taylor & Francis, 3rd edn, 2005, ch. 11, p. 501. 33 H. Feng, J. Tang and R. Cavalieri, Trans. ASAE, 2002, 45, 129. 34 P. Chantaro, S. Devahastin and N. Chiewchan, LWT–Food Sci. Technol., 2008, 41, 1987. 35 F. D. Romelle, P. A. Rani and R. S. Manohar, European Journal of Food Science and Technology, 2016, 4(4), 12. 36 M. F. Sato, R. G. Vieira, D. M. Zardo, D. L. Falcão, A. Nogueira and G. Wosiacki, Acta Sci., Agron., 2010, 32(1), 29. 37 S. Bhushan, K. Kalia, M. Sharma, B. Singh and P. S. Ahuja, Crit. Rev. Biotechnol., 2008, 28, 285. 38 O. Sipahioglu and S. A. Barringer, J. Food Sci., 2003, 68(1), 234. 39 V. Komarov, S. Wang and J. Tang, Permittivity and Measurements, in Encyclopedia of RF and Microwave Engineering, ed. K. Chang, 2003, DOI: 10.1002/ 0471654507.eme308. 40 T. Auksornsri, J. Tang, Z. Tang, H. Lin and S. Songsermpong, Innovative Food Sci. Emerging Technol., 2018, 45, 98. 41 B. Ling, X. Liu, L. Zhan and S. Wang, Sci. Rep., 2018, 8, 4427. 42 A. Kouchakzadeh, Int. J. Emerg. Sci., 2013, 3(3), 303. 43 T. Kaur Kataria, J. L. Olvera-Cervantes, A. Corona-Chávez, R. Rojas-Laguna and M. E. Sosa-Morales, Int. J. Food Prop., 2017, 20(12), 2944. 44 Z. Zhu and W. Guo, Sci. Rep., 2017, 7, 9311. 45 D. Acierno, A. A. Barba andM. d'Amore, AIChE J., 2003, 49(7), 1909. This journal is © The Royal Society of Chemistry 2020 http://creativecommons.org/licenses/by-nc/3.0/ http://creativecommons.org/licenses/by-nc/3.0/ https://doi.org/10.1039/c9ra10639a Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products Effect of temperature and moisture contents on dielectric properties at 2.45 GHz of fruit and vegetable processing by-products